heyuan952568@gmail.com
+86 18730808985
Hebei, China
Phone: +86 18730808985
Email: heyuan952568@gmail.com
Contact: zihao zu — Sales Director
Moving a patient who requires substantial caregiver assistance is not only a transportation task. In professional care environments, staff also need to consider how the equipment is positioned, how the patient remains supported during the handover and how the receiving trolley is secured before transportation continues.
The JH-OCT105 is a specialized patient transfer system built around two mobile trolley units and one transferable patient platform. At the designated transfer point, the two trolley units can be adjusted to the same level, allowing the patient platform to slide from one mobile base to the other.
After the platform reaches the receiving trolley, it automatically locks into position. A secondary safety mechanism provides an additional securing step before the transfer procedure is completed.
The JH-OCT105 uses a different operating principle from a standard one-piece stretcher.
The patient remains supported on a movable platform, while two separate trolley units provide mobility on either side of the transfer point.
When the trolleys are correctly aligned, the platform moves between them instead of requiring the complete trolley base to pass through the docking point.
Before beginning the transfer, staff can position the sending and receiving trolley units at the designated handover location.
Both trolley units are height-adjustable. They can be brought to the same level before movement of the patient platform begins.
The complete system has an overall specification of L3650 × W640 × H640–970 mm.
Both trolley units are equipped with central braking systems. The mobile bases can therefore be secured after positioning and before the sliding transfer procedure.
The patient platform travels along the docking track using four quiet-running rollers installed underneath the platform.
Once the platform reaches the receiving trolley, the automatic locking mechanism secures it in position.
An additional safety device provides another securing element after the platform has reached the receiving trolley.
After the platform has been correctly secured, the trolley units can be separated and the receiving trolley can continue to the next care or treatment area.
Patients who depend on staff for movement may require greater assistance during transfers between different equipment or treatment areas.
The JH-OCT105 addresses the docking stage by allowing the patient support platform itself to move between the two trolley bases.
The patient therefore remains on the transferable platform while the platform changes from the sending trolley to the receiving trolley.
The docking track is manufactured from A380.2 high-strength die-cast aluminum alloy.
The track provides the guided path used by the patient platform during movement between the two trolley units.
Together with the four quiet-running rollers beneath the platform, it forms the core transfer structure of the docking system.
The patient platform automatically locks after reaching its correct position on the receiving trolley.
A separate safety mechanism provides an additional securing function before the trolley continues transportation.
The locking and safety components are manufactured from 304 stainless steel.
This mechanical securing arrangement is an important part of the transfer procedure because the movable platform must be correctly retained after it changes from one trolley base to the other.
Because the JH-OCT105 consists of two independently mobile trolley units, staff need to control the position of both bases during docking.
Each trolley unit is equipped with a central braking system, allowing the mobile bases to be secured after they have been positioned and height-aligned.
This creates a clear workflow for staff: position, align, brake, transfer, lock and continue.
The complete JH-OCT105 system uses eight Ø150 mm central-control casters.
The caster structure incorporates PA6 main frames and wheel cores together with TPU wear-resistant treads.
Precision ball bearings support caster movement, while the wheel design is specified for reduced noise and vibration during transportation.
The standard configuration also includes one Ø100 mm directional wheel.
This component provides additional directional assistance when staff need to guide the trolley along a controlled transport route.
The patient platform is equipped with molded ABS engineering-plastic lift-up side rails.
The rails provide lateral protection around the platform when raised.
When staff require closer access during patient handling, the lift-up structure allows the side rails to be repositioned according to the transfer procedure.
The patient platform incorporates a gas-spring assisted backrest.
The gas spring provides supporting force during adjustment of the back section, allowing staff to change the patient's upper-body position according to the care or transport situation.
The supplied technical documentation does not specify a numerical backrest angle, so no unsupported adjustment range is assigned to the JH-OCT105.
The main trolley body is manufactured from welded carbon structural steel.
The steel structure undergoes surface preparation and rust removal followed by electrostatic resin powder coating.
The docking track uses a different material: high-strength A380.2 die-cast aluminum alloy.
This distinction is important when evaluating the product structure because the aluminum alloy specification applies to the transfer track rather than the entire trolley body.
The patient platform is manufactured from molded ABS engineering plastic.
Four quiet-running rollers are positioned underneath the platform, allowing it to move along the docking track during transfer.
The same technical documentation specifies molded ABS engineering plastic for the lift-up side rails.
A two-section adjustable IV pole is included in the standard product configuration.
The IV pole is manufactured from 304 stainless steel and has a specified diameter of Ø19 mm.
It provides an integrated location for compatible infusion support during patient transportation.
The sending and receiving trolley units have defined roles during the docking procedure.
The two trolley units can be adjusted to the same level before the patient platform begins to move.
Both mobile bases can be secured after positioning and alignment.
The patient platform follows the A380.2 aluminum alloy track using four rollers installed underneath.
The platform automatically locks when it reaches the receiving trolley.
An additional safety mechanism provides another securing step before the trolley units are separated.
This sequence gives care teams a defined equipment-handling process rather than treating the transfer as a single uncontrolled movement.
The JH-OCT105 is primarily designed for hospital patient transfer and operating room workflows where a dedicated docking point is required between separate transport areas.
In long-term care institutions with appropriate clinical transfer areas, the same docking concept may also be considered for patients who require substantial staff assistance.
Facility layout, clinical requirements and internal transfer procedures should be evaluated before selecting this type of specialized equipment.
Professional rehabilitation or continuing-care facilities with defined patient transfer zones may also evaluate the JH-OCT105 where a dual-trolley handover workflow is required.
This is specialized institutional transfer equipment and should not be treated as a general-purpose resident transport chair or ordinary home-care mobility product.
Model: JH-OCT105.
Product Type: Institutional Patient Transfer Trolley with Dual-Trolley Docking System.
Primary Application: Hospital and operating room patient transfer.
Overall Size: L3650 × W640 × H640–970 mm.
Height Range: 640–970 mm.
Transfer Configuration: Two trolley units with one sliding patient platform.
Docking Track: A380.2 high-strength die-cast aluminum alloy.
Main Trolley Structure: Welded carbon structural steel.
Surface Finish: Electrostatic resin powder coating.
Patient Platform: Molded ABS engineering plastic.
Platform Movement: 4 quiet-running rollers.
Platform Locking: Automatic locking mechanism.
Secondary Securing: Additional safety mechanism.
Locking and Safety Components: 304 stainless steel.
Backrest: Gas-spring assisted adjustment.
Side Rails: Molded ABS lift-up side rails.
Main Casters: 8 × Ø150 mm central-control casters.
Caster Structure: PA6 main frame and wheel core with TPU tread.
Braking System: Central braking on both trolley units.
Directional Wheel: 1 × Ø100 mm.
IV Pole: Ø19 mm two-section adjustable 304 stainless steel IV pole.
Net Weight: 135 kg.
Gross Weight: 180 kg.
Main Trolley Packing Size: 2080 × 740 × 800 mm.
Secondary Trolley Packing Size: 1920 × 680 × 615 mm.
The separate packing dimensions can help institutional buyers and medical equipment distributors estimate warehouse space, international freight and project delivery requirements.
The JH-OCT105 combines two mobile trolley units with a transferable patient platform to create a structured docking workflow for assisted patient transfer.
Its operating sequence is straightforward: position the equipment, align the trolley heights, secure both bases, slide the patient platform, confirm automatic locking and the secondary safety mechanism, and then continue transportation with the receiving trolley.
For facilities evaluating specialized transport solutions, explore our Patient Transfer Equipment range.
For residents requiring long-term bedside care, explore our Nursing Bed range.
For technical specifications, institutional projects, bulk purchasing or OEM/ODM requirements, contact us with your requirements.
The nursing beds meet our daily care requirements very well. The products arrived in good condition, and the overall purchasing experience was smooth and professional.
We were looking for a supplier that could provide stable quality and flexible OEM service. Their responsiveness and product consistency have helped us grow our business.
The care beds are comfortable, easy to operate, and well received by both residents and caregivers. The team provided helpful support throughout the purchasing process.
We have purchased care beds for several projects, and the product quality has been consistent. Communication was clear, and delivery was arranged on schedule. A reliable supplier to work with.
Yes. We provide OEM and ODM services for care beds, nursing beds, and healthcare furniture, including customization of functions, colors, logos, packaging, and specifications.
Our products are manufactured under ISO 9001 and EN ISO 13485 quality management systems. Specific certifications may vary depending on the product model and market requirements.
Production time depends on the product type and order quantity. Most standard care bed orders can be arranged within the agreed production schedule.
MOQ varies by product model. Please contact us with your requirements, and we will recommend the most suitable purchasing solution.
Yes. We provide product guidance, technical documentation, and responsive after-sales support to help customers use and maintain our care beds efficiently.
Send us your inquiry today and receive product details, quotations, and professional support within 24 hours.
+86 18730808985
Mon-Fri, 8am-6pm CST
heyuan952568@gmail.com
We reply within 24 hours
+86 18730808985
Instant messaging available
Yintai Industrial Park, Jizhou District, Hengshui City, Hebei Province, China
